Anti gravity device shematics Alexey CHEKURKOV

[Mayhem]

@Impulsiveliar here' some stuff for ya to check out

Alexey Chekurkov Graviflyer -- Levitation device schematics, video, &c

 

[Impulsiveliar]

People have tried to contact him before and somewhat failed, but good luck.

most likely the russian government doesnt allow it thats why even talented russian artist are not allowed to import any of their art

 

[Impulsiveliar]

im studying shematics, does this seem right? & there was a metal Alexey CHEKURKOV used. What could that metal have been? it is a metal with inprints. he mentioned it was hard or expensive to buy?Alexey Chekurkov Graviflyer -- Levitation device schematics, video, &c



View attachment 11605

Alright I ordered some of that rigid steel

 

[TimeFlipper]

The Checkurkov Graviflyer video looks very much like the Thomas Townsend Brown experiments whereby he made his "flying saucers" levitate and move at great speeds...He used a dielectric material for his flying saucers together with huge amounts of voltage with very low currents running through them...

The small flying saucer of Checkurkov was more than likely built from some lightweight dielectric material attached to a 12 volt car battery that probably goes into a DC to AC converter, which finds it way into the small Tesla coil for voltage amplification and then into the Graviflyer, not necessarily in that order...

The Graviflyer would store up a reasonable amount of high voltage for a short period of time, which would allow it to levitate, after it was disconnected from the amplified 12 volt car battery on the ground....Notice the similarity of Checkurkovs Graviflyer to Thomas Townsend Browns device resting on floor back in 1958, (its a very short video clip starting at 1 minute 33 seconds into the video) ....Checkurkovs video is underneath the Thomas Townsend Browns video..

 

[steven chiverton]

ive collected Alex chukerkovs videos and noticed the edge of one of the spining discs is peeled away showing what looks like either a plastic or fiber glass disc underneath so the metal covering looked like alliuminium metal like contact paper of some kind and hes using rf currents from the top of the coil which ive always suspected rf currents or rf power helps greatly the whole set up looks like a spinning rf capacitor plates with magnets attached

 

[Impulsiveliar]

ive collected Alex chukerkovs videos and noticed the edge of one of the spining discs is peeled away showing what looks like either a plastic or fiber glass disc underneath so the metal covering looked like alliuminium metal like contact paper of some kind and hes using rf currents from the top of the coil which ive always suspected rf currents or rf power helps greatly the whole set up looks like a spinning rf capacitor plates with magnets attached

It can’t be plastic it explodes I watched a couple videos

 

[Impulsiveliar]

ive collected Alex chukerkovs videos and noticed the edge of one of the spining discs is peeled away showing what looks like either a plastic or fiber glass disc underneath so the metal covering looked like alliuminium metal like contact paper of some kind and hes using rf currents from the top of the coil which ive always suspected rf currents or rf power helps greatly the whole set up looks like a spinning rf capacitor plates with magnets attached

we need the physics behind it what causes the phenome & from there tests can be done to see how much power the unit needs

 

[Impulsiveliar]

so the magnetics from my under standing have to be pointed NSNSNSNSNSN perfectly ,and wires connecting to separate parts of the device. to create magnetic disk, need a HV and a Tesla coil one aluminum disk, two smaller disks, 4 rods and 4 steel plates for holding the unit.

 

[TimeFlipper]

ive collected Alex chukerkovs videos and noticed the edge of one of the spining discs is peeled away showing what looks like either a plastic or fiber glass disc underneath so the metal covering looked like alliuminium metal like contact paper of some kind and hes using rf currents from the top of the coil which ive always suspected rf currents or rf power helps greatly the whole set up looks like a spinning rf capacitor plates with magnets attached

Any thoughts on what the frequency of the RF would be cobber?

 

[steven chiverton]

It can’t be plastic it explodes I watched a couple videos

i watched the videos to and the discs only spin slow, slow enough to easily still see the magnets attached to them, and in another video the set up dosent have the pezio transducer on the top so i think it may not have to really use it and that it may be just a distraction