hyper dimensional resonator electromagnet

here's the latest when i first fired up the new hyper dimensional resonator i used the 240vac to 120v ac at 50hz converter and the 7.8 layered electromagnet always had the 2 powerful disc shaped rare earth magnets stuck to the front end , and if i was to use the 240vac without the convertor it always makes the watch spin even with the magnets at the front like i did in former tests with the hdr number 3 .now the crystal unknown to me had already been programmed but only from all the nights i laid in bed handling it so when i tested the new hdr the first time i didn't have the crystal in the witness well so when i later put it in the programing in the crystal allready then went through the electromagnets and altered the rare earth magnets in a way so when i fired it up it wouldn't effect the watch like it did before just made the watch stop but latter i found with very much tries, an area so fine that it be hard to find it again to hold the watch in it to get it to spin but then by removing the 2 disc shaped powerful rare earth magnets the time field or whatever they say it is was re established but without the magnets and the watch easily spins again, but not when the watch is moved along the side of the electromagnet , now i've read somewhere that after having the a magnet stuck to the hdr electromagnet you can program it or just put it to your navel area so if that's the case then maybe the magnets do get some form of programing if they do, so i think this may be the case if not i'm at a loss to try explain it in any better way, so to confirm this ill get 2 new powerful rare earth disc shaped magnets and try the 2 new ones out like before and without the crystal in the witness well to confirm this
 
hm ive got magnetic field sensors in the milligauss readings a number of different ones i brought on e bay ones a ghost detector it has up to 40 plus milligauss that's what it says at full reading it doesn't tell you how high above 40 it goes but.
the latest instrument i got recently is the cell phone sensor like steven gibbs has, and a sphere shaped quartz crystal ball and i got before a tourmaline pyramid and rocks to
 
i've already started preparations to try tap into the quartz crystal to monitor anything in it so ill share it when i get it done and if i get any results ,
 
i've already started preparations to try tap into the quartz crystal to monitor anything in it so ill share it when i get it done and if i get any results ,
there is one more thing i may of forgotten to mention and that's when i was bringing up one out of two test watches to the front of the 7.8 layered electromagnet with the 2 rare earth magnets stuck to the front i felt some kind of energy like heat but the magnets weren't even getting warm enough then , this was very strange as if some kind of invisible energy was emitting from the right side of the rare earth magnets into my right hand
 
i've completed the wiring for my 5th hyper dimensional resonator prototype, using the new trifilar caducous wound spiral coil , and i used the strait 240vac 50 hertz mains voltage without the 240vac to 120vac convertor, i used a capacitor marked as 474 i think it was as i just couldn't be bothered waiting for the 0.1uf 250v capacitors to come in the mail , i used the same 7.8 layered electromagnet that creates the multipole fields when run off the hdr number 4 and the test watch spun forwards fast at the front of the electromagnet and along the sides to , and to my surprise at the front there's a field that spins the watch in the opposite direction so ive got another multipole feild that i found when i moved the watch to a certain position at the front near the north pole field so this makes 2 hdr units that create this multipole field and for the 3rd caducous wire in the trifilar wound pancake rubbing coil i ran the ends of the wires from that third wire to terminal posts at the front under the time coil posts but theses are not lined up with the time coil posts due to lack of space behind that part panel of the circuit box i used, due to me installing a ac core filter . so that third wire will be the experimental one for ac rf signal injection or just run a frequency through it from my feeltech frequency generator , or run it to a vortex
 
i've completed the wiring for my 5th hyper dimensional resonator prototype, using the new trifilar caducous wound spiral coil , and i used the strait 240vac 50 hertz mains voltage without the 240vac to 120vac convertor, i used a capacitor marked as 474 i think it was as i just couldn't be bothered waiting for the 0.1uf 250v capacitors to come in the mail , i used the same 7.8 layered electromagnet that creates the multipole fields when run off the hdr number 4 and the test watch spun forwards fast at the front of the electromagnet and along the sides to , and to my surprise at the front there's a field that spins the watch in the opposite direction so ive got another multipole feild that i found when i moved the watch to a certain position at the front near the north pole field so this makes 2 hdr units that create this multipole field and for the 3rd caducous wire in the trifilar wound pancake rubbing coil i ran the ends of the wires from that third wire to terminal posts at the front under the time coil posts but theses are not lined up with the time coil posts due to lack of space behind that part panel of the circuit box i used, due to me installing a ac core filter . so that third wire will be the experimental one for ac rf signal injection or just run a frequency through it from my feeltech frequency generator , or run it to a vortex
Back in the 1930s when Tesla using the name of Turbo, was working for National electronics, he created time coils for several receivers that were used in the Philadelphia Experiment...He arranged the coils in a triangular (Delta) shape :)
 

Top